10.0mm²-Black/Red (H1Z2Z2-K) Single core Solar (PV) Cable (NO.7194004)- IEC 62930 / EN 50618:2014
Product Description
10.0mm⊃2;-Black/Red (H1Z2Z2-K) | ||||||
General characteristics: | ||||||
Appllcation: | ||||||
Specifically designed to connect photovoltaic system components inside and outside buildings | ||||||
Cable Construction： | ||||||
Conductor | ||||||
Metarial： | Tinned annealed copper | |||||
Area(mm⊃2;) : | 1*10.0 | |||||
Construction(N/mm) : | 74/0.40 | |||||
Conductor(Dia./mm) : | 3.97 (Ref.) | |||||
Insulation | 125℃ XLPE Black | |||||
Nom. thickness (mm) : | 0.8 (Ref.) | |||||
Standard diameter (mm) : | 5.6±0.10 | |||||
Jacket | 125℃ XLPE, Black / Red | |||||
Min. thickness (mm) : | 0.7 | |||||
Nom. thickness (mm) : | 0.9 (Ref.) | |||||
Outer diameter (mm) : | 7.40±0.1 | |||||
Making | ZION COMMUNICATION TÜV SÜD IEC62930 | |||||
Package： | ||||||
100M/Roll, 500M/Wooden Drum | ||||||
PALLET | ||||||
Electrical properties | ||||||
Nominal Voltage: | H1Z2Z2-K: DC 1.5KV AC 1.0/1.0KV | |||||
Ambient Temperature: | -40℃~+90℃ | |||||
Max.Temperature at conductor: | +125℃ | |||||
Service life: | ＞25 years ( -40℃~+90℃) | |||||
Voltage: | 600/1000V | |||||
Temperature: | -40~90℃ | |||||
Conductor resistance (20℃): | 1.95Ω/km | |||||
Insulation resistance (70℃): | ≥1000 MΩ/km | |||||
Withstand voltage(V/5min) | AC6500 | |||||
Speak voltage(V/5min) | AC6500 | |||||
Min bending radius(mm) | 5*D | |||||
Main performance parameter of finished cable | ||||||
Voltage test of finished cable | ||||||
Min.time of dipping in water | ≥1(h) | |||||
Testing voltage (AC) | 6500(V) | |||||
Min.voltage applying time at one time | 5(min) | |||||
Test result | no breakdown | |||||
Sheated surface resistance | ||||||
Length of specimen: | 250mm | |||||
Test result | ≥109Ω | |||||
Penetrate the insulation resistance | ||||||
Temperature | 20℃ | |||||
Test result | ≥1014Ω | |||||
High temperature stress | ||||||
Temperature | 140℃ | |||||
A: with 1.2 Voltage test | A: No breakdown | |||||
B: deep pressure | B: Wall thickness 50% | |||||
Damp-heat test | ||||||
Temperature | 90℃ | |||||
Humidity | 0.85 | |||||
Aging before and after the tenslle strength of Change | ≤30% | |||||
Aging before and after the elongation at break of Change | ≤-30% | |||||
Acid-alkali Resistance | ||||||
Min.time of dipping in | 168h | |||||
Aging before and after the tensile strength of Change | ≤-30% | |||||
Elongation | ≥100 | |||||
Low-temperature bending | ||||||
Temperature | -40℃ | |||||
Time | 16h | |||||
Test result | No crack | |||||
Ozone resistance | ||||||
Ozeone concentration % | （200±50）x10-6 | |||||
Time | 72h | |||||
Test result | No crack | |||||
Heat schrinkable jacket test | ||||||
Test result | ≤2% | |||||
Flame retardant-Vertical burn | ||||||
Flxture on the lower edge from the starting point and carbonization | ≥50mm | |||||
Burning fuel downward from the lower edge of bottom fixture | ≤540mm | |||||
Halogen content of non-metallic materials | ||||||
Test result | ||||||
Chlorine and bromine content | HCL≤0.5HBr≤0.5% | |||||
Fluoride content | F≤0.1% | |||||
The inner layer of insulation and sheath of the mechanical properties | ||||||
Test result | ||||||
Aging before tensile strength | 8.0N/mm⊃2; | |||||
Aging before elongation | 1.25 | |||||
Aging before and after the tensile strength of change | -30% | |||||
Aging before and after the elongation at break of change | -30% | |||||
Hot extension | ||||||
Temperature | 200℃ | |||||
Test result-The inner layer of insulation and sheath | ||||||
Elongation under load | ≤100% | |||||
Elongation after unloading | ≤25% | |||||